Category Archives: led street light

The advantages of LED street light:

1. Energy conservation, energy saving about 40% than traditional light.
2. Long life, theoretically can work 50000 hours, generally can reach 30000 hours.
3. Environmental protection, do not contain harmful substances.
4. Point light source, light distribution design, precise control illumination distribution, improve the utilization rate of light.
5. Installation and maintenance cost can save a lot.

New Zealand and Denmark are using intelligent LED street light

Having been introduced,intelligent LED street light has been enjoying a great popularity in the lighting market, and now many cities around the world are eager to prepare large-scale use smart LED street light system in urban. New Zealand capital Wellington in the near future plans to become the first city using intelligent LED street light system in southern hemisphere. The city plans to replace all of the city’s municipal streetlight excluding the CBD area with intelligent LED street light, the total number of the streetlight to be replaced is approximately 18,000. These LED street lights can automatically reduce the brightness when nobody passes, while the streetlights in CBD area usually lights up throughout the night, and therefore there is not urgency and necessity to carry out the replacement of street lamp.

Wind Solar Hybrid LED Sreet Light LED street lighting application LED street light LED-street-light-cl3-168w LED-street-light led-street-light-150w smart street light    solar street light Street Light irradiated area Schematic    Streetlight structure diagram

In Europe, the Copenhagen city of  Denmark  is also test the intelligent LED street lights which would be used in the city through the establishment of a common garden. In September the city will built a the test zone called “Danish Outdoor Lighting Laboratory” (DOLL) on the outskirts of Albert Sloan area where a number of the company’s intelligent outdoor lighting products will be tested. Many members of the public will also be invited to participate in the pilot test. Copenhagen city plans to achieve “carbon balance” in 2025, this experiment park established is one of the efforts to achieve this goal.

Article from http://www.sanhelighting.com/index.php/new-zealand-and-denmark-are-using-intelligent-led-street-light/

LED street lights are enjoying a great popularity over the world especially in China

Outdoor lighting including: Lawn lamp, garden lights, tunnel lights, flood lights, underwater lights, street lights, wall lights, landscape lights, buried lights, compared with the home lighting,outdoor lighting is known as power, brightness, bulky, long lifespan, low maintenance costs. It is worth noting that LED street lights dominate the outdoor lighting applications. Los Angeles plans to mount 140,000pcs LED street lights within five years, while all of the street lights in Pennsylvania Ambler) and Sunbury are replaced with LED street lights, LED street lamps are commonly used in other countries, such as Japan, Korea and so on. In China, all of the road lighting applications will adopt the LED street lights within three years in Dongguan city Guangdong province, Hainan plans to achieve within five years. Beijing Olympic Games, Shanghai World Expo and Guangzhou Asian Games infrastructure also makes extensive use of LED outdoor lighting, such as there are 70,000 LED street lights were built on the surrounding roads of Guangzhou Asian Games venues and the main stadium, 12,000 high pressure sodium lamp are all transformed into LED streetlights on 12 surrounding main roads of Foshan Lingnan Pearl Stadium arena.

LED street lighting comparison LED street light comparison LED street lighting application LED street light LED-street-light-cl3-168w LED-street-light-cl3-168w (1)led-street-light-150w

We can say that street light is an important part of urban lighting. The traditional streetlights are high pressure sodium lights, the pressure sodium lamp with low overall efficiency caused a huge waste of energy, therefore, the development of new urban energy saving and environmentally friendly street lighting with high efficiency, long lifespan, high color rendering index has a very important significance. In recent years, LED street lights is enjoying a great popularity in the world especially in China, the market scale has been expanded.

In addition to the road outside lighting, LED outdoor lighting is also widely used in urban landscapes, tunnels and so on. In fact, as we have been pursuing energy conservation and environmental protection, and intelligent lighting, there are dramatically changes in lamps, light, material, style and design ways.

China’s large population and rapid urbanization development attribute to the quite fast road construction, which has a significantly demand for LED street lights and LED landscape lighting and other outdoor lighting. According to authoritative survey shows that the growth rate of China outdoor lighting industry is more than 40 percent per year, the output value is expected to exceed $ 3.5 billion in 2014, it is expected to reach $ 4.7 billion in 2015.

Article from http://www.sanhelighting.com/index.php/led-street-lights-are-enjoying-a-great-popularity-over-the-world-especially-in-china/

US Monterey Park City’s public street lights will be replaced with the LED street lights within two years

Huang Weigang,Mayor of Monterey Park City published the municipal report of 2014 and future municipal planning. Monterey Park ( commonly referred to as the Mongolian Chinese American city) is a small city in Los Angeles County, California, located in the east of Los Angeles, on the foot of King Hills of the San Gabriel Valley. Huang Weigang said the city has just agreed with recently that all of the household water meter in the city will be updated within a year, while the city’s public street lights will be replaced with the LED street lights within two years, which is not only to save electricity, but to improve the lighting function. In the near future the city will usher in two large shopping centers, three hotels.

HPS lights VS LED street lights High Power LED Street Lights SP90 Photometric Performance

He said the city through municipal transparency is to allow the residents to know and oversight of the city’s each policy, and encourage people to actively provide suggestions and advice to help more perfect urban construction. Today Monterey Park City has installed giant screen in the city hall of municipal government, scrolling to play ongoing projects and future planning of the city at this stage. With the joint efforts of us, we eagerly expect that the Mongolian city can continue to develop  so that every citizen to enjoy a comfortable life.

comparison of high pressure sodium and LED street light  led-street-light-100w-120w

That night, the incumbent Federal House of Representative, Mr Zhao, Congressman Ed Royce and other guests were present.

Article from http://ledindoorlighting.cn/index.php/us-monterey-park-citys-public-street-lights-will-be-replaced-with-the-led-street-lights-within-two-years/

Design Lighting Tokyo Opens a Window for Future of Lighting Design

As lighting technology improving, people begin to be aware of the importance of good lighting surroundings. In order to give stages to people who work in lighting related industries and exchange their great ideas, Reed Exhibitions organized “Lighting Japan” in Tokyo, Japan. In this internationally open exhibition, you can meet manufacturers, contractors, designers and end-users as well as the newest discovery, technology, products and lighting design concepts.

Reed Exhibitions is the largest trade show organizer in Japan, organizing more than 90 shows and exhibitions every year. Now, Reed Exhibitions is preparing for Lighting Japan, an event that will be open from 13th to 15th January in 2014 in Tokyo. This large exhibition is constituted by three minor exhibitions: the 6th LED panel lighting wholesale Technology Expo, the 4th LED / OLED Light Expo and the 2nd Design Lighting Tokyo The previous two exhibitions focus on developing, producing and negotiating between manufacturers, contractors, researchers and users while. Design Lighting Tokyo will be specifically engaged into lighting design.

In recent years, lighting has become a professional field that can not be limited by optics or electricity. Moreover, light can be a representation of aesthetic taste and cultural background rather than simply a medium that illuminates a space. Henceforth, Reed Exhibitions organized the first Design Lighting Tokyo. As a part of Lighting Japan, Design Lighting Tokyo stresses on display of innovative lighting products and opinions provide by lamp producers, interior designers, architects and lighting designers. In the venue, there will also be lighting experience pavilions for visitors to observe different lighting conditions and products. Exhibitors can also communicate with visitors face to face on their solutions and ideas toward lighting design.

Design Lighting Tokyo is one of the most influential events about lighting design around Eastern Asia because Japan possesses a special position as a symbol of eastern beauty. Japan, South Korea and Taiwan are regions that pay more attention to sense of beauty in daily lives, and there are many excellent led street light wholesale designers from these three places. This is an event that attracts lots of lighting designers from globe to exchange their perspective, it is also highly possible that visitors can meet these exceptional lighting designers so they can learn more knowledge about lighting design .

How to improve the brightness of LED lighting lamps

LED brightness can be improved through the following two methods: 1. To increase the light output of the chip itself: light output can be increased through improving the luminescence efficiency of the chip’s active layer or improving the external light extraction efficiency by optimizing chips’ shape or making larger scale chips that run high density current. 2. To use the light effectively. In other words, to increase the amount of light that irradiate towards the needed direction. In this method, light wave control technology is used. Through a better design of the optical structure shaped by the packaged epoxy resin, the light can be controlled to shine towards expected direction, thereby improving the brightness of LED. The above are the methods to improve led street light wholesale, if the brightness of LED display runs under expectation, methods listed below can be adopted: 1. To alter the current magnitude that runs through the LED Generally, LEDs allow a 20 milliampere operating current continuously Only red LED has saturation phenomenon, other LEDs’ brightness are in direct ratio with the current amount.. that runs through them. 2. To realize grey scale control through adopting PWM (Pulse-Width Modulation) method. That is to change the width of the light pulse (duty cycle) periodically. If the time for the relighting cycle is short enough (in other words, the refresh rate is high enough), the dithering of the luminescence pixel can not be felt by eyes thanks to the visual persistence trait. As it is more adaptive to adopt digital control to realize PWM, meanwhile, as microcomputer is widely used to provide the content to display in LED screens, nearly all of the LED control systems are composed by main controller, scanning board and display control device. Main controller firstly captures data of all colors’ brightness in one particular screen image from the display adapter, then to distribute the data to the scanning boards. Each scanning board takes charge of certain rows of the LED display and the LED display control signal in each row can be transmitted in serial mode. Currently, there are two serial modes to transmit display control signal. One way is to make centralized control of each pixel’s grey scale in the scanning board More detailed steps:. the scanning board analyzes the data of each row of pixel received from the controller (PWM process), then the board will transmit the open signal of each row to corresponding LED light, controlling each LED to be lit on or to keep off state. The signal is transmitted in serial mode and in the form of pulse (the pulse signal will be 1 if it indicates LED to turn on, contrary, the signal will be 0 ). The device used in this method is less, but the data amount being transmitted is comparatively larger. In every relighting cycle, the grey scale level is in direct ratio with its pulse amount for each pixel, that is to say, 16 grey scale levels need 16 pulses and 256 grey scale levels need 256 pulses. As in led street lighting fixture, the working frequency for the devices is limited, only 16 grey scale levels is achieved generally. 3. The serial transmitting content for the scanning board is not the on or off signals of each LED, but an eight-bit binary brightness value. If every LED has its distinct PWM to control its lighting time, a pixel under 16 grey scale levels need only 4 pulses and 256 grey scale levels need only 8 pulses in one relighting cycle, reducing serial transmission frequency greatly. Through this grey scale decentralized control method, 256 grey scale levels control can be achieved easily.

LED —— The Fourth Generation of Automotive Light Source

The structure of modern automobile lamps is becoming more and more complicated, at the same time the function is being improved gradually. The development of automobile lamps has experienced four stages.

The first generation of led street light wholesale source is fuels (candles, coal oil or acetylene). These fuels burn to emit lights. Fuels can only satisfy the requirement of early stage automobile lamps due to its low luminous efficiency, weak light intensity, unstable performance, complex operation and etc. shortcomings.

The second generation of automotive light source is incandescent lamp. Incandescent lamp was invented by Edison in 1879. In the year 1913, Americans for the first time apply incandescent lamp in Cadillac cars to act as headlamps. From then on, automobile lamps have undergone a series of revolutionary reformations and the automotive illumination has entered the electric age. Following that, new technologies like reflector, starter, generator and storage battery were invented successively. It was not until the year 1925 that the automobiles adopted incandescent lamps widely. In 1950s, halogen tungsten lamp was invented and quickly become the dominating light bulb for automotive strong light source.

The third generation of automotive light source is HID (high intensity discharge). Be provided with advantages of high luminous efficiency, high brightness and high reliability, HID has replaced incandescent lamp and halogen tungsten lamp to become a new choice for automotive light source.

Now comes the fourth generation of automotive light source -.. LED LED is a kind of semiconductor products with PN junctions When a positive bias was imposed on the two ends of the PN junctions, the PN junction system was activated, and the carriers will shift from low state of energy into high state of energy. On this condition, unstable carriers in high state of energy will return to low state, thus generates superfluous energy which will be released in the form of photons, according to the conservation of energy principle . That is LED’s illumination principle. Unlike earlier stages light sources, led high bay light price does not shine light because of temperature rising caused by heat energy. In LED, the electric energy is switched into light energy directly. The wavelength of the light irradiated by LED is decided by the carriers’ energy difference between low state and high state.

The application of LED in inner automobile light source is becoming wider. It is widely used as accessorial illuminating lamps, backlight of instrument panel and so on in particular.

The five basic components for LED automotive headlamp are: LED array, reflector, lens, radiator, and driving circuit.

The development of LED automotive light source is in direct association with the development of LED products. Only when LED illumination technologies make advancements can LED be more widely used as automotive headlamps. In the near future, with the improvement of LED quality and the reducing of prices, LED products will bring on a new revolution in the illumination domain, which will further influence the transformation of automobile lamps.

Developments in Solar Powered LED Surveillance Lights

A UK solar light blog outlines some of the latest developments in solar LED surveillance lights. Security illumination is seen as one of the essentials to protecting your property. The instalation and running costs have now been shattered to make this aspect of security available to all. So have a look at the new lines of security lighting.

Saving energy is definitely big on the agenda at the moment and with the advent of the solar panel came a plethora of new products. One lesser known innovation that has yet to take the world by storm is the development of the white led street light with solar panel. But this is a truly remarkable development.

The humble red diode. Otherwise referred to as the red stand-bye dot. The Indicator that shows an electrical device is switched on, was given a new role in life. Following years of research the LED was made to glow white. It appears to be a big fuss over what is nothing more than a white light bulb. Now consider the spiraling cost of energy and the lackluster performance of the preceding low energy lighting. Switch on to the crisp white illumination of the LED. You can now get excited about solar powered security lights

The work done by a 100 watt incandescent bulb can now be achieved by a mere 5 watts or less. Couple all this together and include a solar panel and a rechargeable battery. Created is a formidable combination. No longer is it necassary to burn a 500 watt halogen security light. The job can just as easily be achieved with a product such as the L955 solar powered motion activated security floodlight. complete with no less than forty five tiny led street lighting fixture. Combined they crank out a staggering forty lumens. Remarkably the power required for this outstanding performance is provided free of charge. The small solar panel responsible for providing the power to the battery can be positioned up to fifteen feet away from the lamp. So even if the 45 LED Motion Activated Solar Flood light is in a shady spot. You can position the power grabbing solar panel to catch the best of the daylight. Harnessing all the sunshine in a 3600mAhr battery pack, which will discharge as required during the hours of darkness. If needed, a continuous discharge of up to four hours can be achieved. Though normally the lamp would be used in the detect mode. Utilizing the passive motion sensor to provide hours of timed on of periods as required.

Adaption of LED Streetlight throughout America

An average American town’s biggest expense, when excluded payrolls, typically lands on its reoccurring street lighting bill. LED, a prevalent technology now implemented as backlight for many electronic devices, such as Tablet PCs, Smartphones, TVs, and more, looks promising to cut expense by reducing electricity consumption up to 50% and maintenance required in streetlights.

Culpeper, Virginia, a town of approximately 16,000 people recently erected two led street lighting Manufacturer, with one on North Main Street and the other on Piedmont Street. A third LED streetlight is said to be installed in South Main and Elm streets. According the town’s press release that the town is not rushing into LED streetlights, officials hope through installing and experimenting different LED streetlights, its residents will decide on what style and foot print of the lights they would like to have installed. Officials say they will seek residents’ opinion and review on the different streetlights in regard to their light efficiency, light color and style.

The town representative also says they are looking for streetlights that would blend-in with the local atmosphere. There are a lot of localities and utilities that can be expected to implement LEDs, said Culpeper town light and power director, Mike Stover. LED consumes 50 percent less in power usage. Despite that a LED streetlight typically cost twice more than the price of incandescent bulb. LED streetlights will pay-off in the long-run. The town has recently converted all its traffic lights into the LED variety. He also added that traffic lights using LEDs are already able to save more by using less expensive battery backup in case of power outage. LEDs are more expensive than traditional incandescent lights, but this difference will be compensated over time. According to LEDinside, LED lights last longer and up to a standard of 100,000 hours, approximately 4 times longer than the 24,000 hours of a regular bulb.

According to the town official, a LED streetlight cost about $ 400 to $ 600, while the traditional high pressure sodium streetlight cost about $ 250. Stover added it does not hurt to look into new options to illuminate our town. After becoming the very first community to convert all of its traffic lights into LED lights, now we (Culpeper, Virginia) are looking into streetlights. LED technology is improving with surging interests while its price drops quickly. LED streetlight accounted for only 1 percent of all streetlights 5 years ago and now the number has grown to 10 percent LED lights are directional;.. they emit light in direction specified while incandescent lights emit lighting in all direction LEDs streetlight produces cooler white light, without the yellowish tint of traditional streetlight.

In Texas, Arlington, official has started converting their high-pressure sodium streetlights into LED streetlights. About one third of the streetlights will be converted starting from the east side of Arlington and progressing west. Official says there will be no detour and traffic delay due to construction. The new streetlight will be white and cooler when compare to the yellow-toned high-pressure sodium lights.

Part of the decision on converting streetlights was a result of a town survey conducted. The survey asked Arlington residents to comment on the kind of streetlight they would like to have installed. Officials placed two different of lights in four different residential areas and town hall. The main differences between these two lights are aesthetic and light temperature. With town in the country trying to reduce cost without cutting jobs, the only way is to decrease long-term energy consumption.

On the other hand, in towns like Centennial, Colorado is having difficulty convincing their utility to participate in adapting LED lights. This city of 100,000 people has battled with their utility to set rates that will be best in adapting LED streetlight. The city wants to adapt LED streetlight because its energy efficiency and low maintenance.

Also in Baltimore, Maryland, towns are discovering bringing in new LED technology is not as easy as they thought. They wrangled with their utility for two years until finally establishing a decision on LED rate structure. Jackson, New Jersey, risked their federal grants as their negotiation with their utility dragged for more than a year.

In Montana, Northwestern Energy lobbied against the state wide adaption of LEDs, saying that the LED lights are not cost effective when served as streetlights. Even in city known for their adventurous approach toward adoption of new technology like Raleigh, North Carolina, has difficulty convincing their utility. Despite LEDs’ price have decreased by half over the past three years, led street lighting fixture is a semiconductor chip that emits light. Still LEDs are twice more expensive than the general high-pressure sodium light commonly used in streetlights. Cities are willing to trade in especially for the long life of LED lights. As typical LED light bulb lasts up to 15 year when compare to a regular bulb that only lasts 3 to a maximum of 4 year.

Some cities own and maintain the streetlight they use, but usually utilities install streetlights in cities and towns, maintain them and charge for the fixture, maintenance and energy cost of the streetlight on a monthly basis.

In Florida, the rates on adopting LED streetlight are twice more expensive than regular high-pressure sodium streetlight. The utility says it is because the replacement costs are very high, due to the fact the state if prone to hurricane and lightening.

Cities that have own their own streetlights make this adoption more quickly, according to the vice president of government relation, Greg Merritt, at Cree. Both Los Angeles and Seattle have municipal-own streetlights, and are undertaking enormous replacement of old high-pressure streetlights with LED units. For Seattle, its program to retrofit a total of its all 84,000 streetlights is aim to save $ 350,000 of its electricity bill in the first year and the number is expect to triple in the following three years with the installation of its 12,000 LED streetlights. The project manager of Seattle streetlight program, Ed Smalley said, “That is money in the bank”.

General Applications of Outdoor LED Lightings

By utilizing LED light bulbs, you are not only going green. There are actually a lot more benefits concerning this conversion. Two of the main reasons help people to decide going green are tax break and helping the environment. led high bay light price will not only be helping our environment but in the long run, it is going to be able to save us a lot of cash on the electric bill because they consumes a lot less electricity.

LEDinside observed LED lights in finding their parts in every aspect of residential home, that been said is to include outside spaces with additional outdoor lightings. LED lights are a type of energy efficient device made to accommodate each and every spot inside and outside of your house , with the objective to deduce the energy wasted in typical traditional lighting and take part in saving the planet. House owners who experience the rewards of LED lights could now be in a quest in converting their outdoor lighting fixtures to LED light bulbs.

Outdoor lightings are types of bulbs equipped capability to work in all possible outside locations, for example like at your terrace and balcony. What is more impressive about these lights’ versatility is that they can be used in conditions such as to light up steps leading to your door. LED illuminations have already found its popular application in outdoor lighting, especially when applied in place like swimming pools that particularly need additional lights throughout the night. If you can visualize a use for LED lighting outdoor, you will find actually there are already existing LED products for that purpose.

LED Lighting for garden and outdoor use has become popular because of LEDs’ affordable and efficient characteristics. LED lights are consisting of clusters of tiny LEDs to produce a bright glow and they have been proven to be highly efficient. A typical LED light can last to more than 50,000 hours and because of this reason, they are an ideal lighting source. Old traditional outdoor lighting typically use high wattage light bulbs in order to produce enough light to light desired areas. Therefore, if lights stay on all nights, lighting electricity cost can accumulate to an astonishing amount on your monthly bill.

Despite the fact that LED lights are the environment friendly choice, many people prefer LED lights for reason of the amount of energy consume, their cost effectiveness and electricity saving characteristics. LEDs provide pure light and generate relatively small amount of heat. Durability is also a factor that makes LED lights a wise choice because they can easily endure harsh environments.

Different from the traditional incandescent light bulbs we are accustomed to, LED lights are long lasting. Also, LED lights are made from solid state components so they do not break as easily as glass incandescent light bulbs. This fact makes them very resilient to external shock and much more durable than fragile incandescent light bulbs. Moreover, LED lights come in various different sizes, shapes and colors, more than what we can expect from the traditional light sources.

LED lightings are capable of emitting intended light colors without using light filters that were require by traditional lighting methods. LED lights can be easily dimmed by either lowering their forward current or by manipulate their pulse-width modulation.

LED lights use approximately 95 percent less energy than the old traditional glass incandescent light bulbs Reasons being that LED bulbs last for years, in addition to the energy saved, there are also less maintenance and replacement relative costs. Costing saving can be a major benefit of using LED lights; most LED light bulbs consume only two to ten watts of electricity to operate.

The longevity of an incandescent light bulb when compare to that of a LED bulb is shocking, a LED bulb while being energy-efficient can last up to approximately 60,000 hours while the of an incandescent light bulb only last about 1,000 hours. A led street light with solar panel last 10 times long than Compact Florescent light bulb and even longer when compare to that of an incandescent light bulb.

Outdoor LED lights are typically use for security, safety, utility and atmosphere purpose. Security lights are mainly motion activated and are mounted to walls outside along a driveway or around a doorway. Safety and utility lights are lights that make you felt safe, by effectively light up pathways, patios and decks.

These outdoor lights can be use effectively to produce pleasing atmosphere. For example ground level LED lights can be used to light up gardens and flower beds, accentuate features of a garden and bringing plants to life. LED spotlights, on the other hand, draw attention to trees or flowers by creating silhouettes behind the desired objects. Uplights are a choice used to create dramatic lighting at the base of walls and other places while Downlights eliminate larger, wide areas including walkways and to increase security. LED rope lights and strings of tiny LED light bulbs can be strung along a fence, on garden borders, branches and around trees.

During big events like Christmas, lighting costs are known to be extremely high. By utilizing LED illuminations in replacement, house owner can cut back on their electricity consumptions. Furthermore these decorative LED lights are the same price as the order traditional decorative lights, leave you no reason to not acquire these energy saving and environmental friendly products. It is a fact that LED illuminations have been use is large size Christmas interior décor due to the great intensity of the light bulb.

The great thing about these LED light bulbs is their dazzling brightness; the light they generate can create a major visibility then traditional Christmas light can not compare These new LED decorative lights can last up to about 30 year and come in different size and shape, guarantee. that most customers can find the light that suit their expected decorative style.

California sets the pace with tough new energy conservation standards

California continues to play a leadership role in energy conservation in North America. As of July 1, strict new energy standards came into force in the form of changes to the state’s building code, Title 24 Energy Efficiency Standards. The goal is to improve energy efficiency in all residential and commercial buildings by 25 per cent and 30 per cent respectively, relative to energy standards set in 2008. According to California Energy Commission estimates, the changes to non-residential standards, which also include HVAC and water heating, will save 372 GWh / year.
. Some of the most significant changes to the code have to do with lighting standards One of these changes is the extended requirement for use of adaptive lighting; lighting that shuts itself on and off, or dims, as needed Another new requirement is that indoor. led high bay light manufacturers in most non-residential buildings must have manual shut-off and dimmer switches so that lights in any room or area of ​​a building can be turned off when not in use Integrated occupancy sensing: daylight harvesting; demand response; continuous dimming; these. are the new normal lighting requirements in California. In retrofit projects, most buildings now will have to meet the same standards for lighting as new-construction buildings. *

Among the new indoor lighting requirements are quality standards for LED luminaires intended for general indoor lighting. In order to qualify as “high efficacy,” LED luminaires must provide a CRI of at least 90, and a CCT of 2700-4000K. There are additional criteria for defining high-efficacy lighting, including lumen output per watt. Lighting fixtures that can accept low-efficacy lamps do not qualify as high efficacy.

All new-built bathrooms, for example, will now require at least one high-efficacy luminaire, while other bathroom lighting must be either high efficacy or adaptive, ie, controlled by vacancy sensors. Kitchens, similarly, will require at least 50 per cent of permanently installed lighting to be high efficacy, and there are wattage limitations for lighting inside cabinets and under shelves.

All of these changes to California’s building code, including the water conservation measures, are expected to add $ 2,000 on average to the cost of a new home, while saving the homeowner an estimated $ 6,000 over thirty years. A document containing a concise summary of these changes also has useful resources for builders and others with an interest in the California energy efficiency standards.

California’s approach to energy efficiency, combining legislation and regulation, has helped to reduce energy consumption across North America by forcing manufacturers to create the higher-efficiency products it mandates California’s clout derives from its sheer size:. The market is huge, with a population about the same as all of Canada’s. As soon as the new code went into effect on July 1, lighting products manufacturers began boasting of their products’ compliance.

It’s difficult to argue with the California approach. “The most effective way to optimize building performance is during construction,” said California’s Energy Commissioner. The state has set a Zero-Net Energy goal for all new residential construction by 2020, and for non- residential construction by 2030.

Are led street lighting for sale in other jurisdictions ready for building code changes that mandate the amount of “daylighting zones” in a building The California code does that:? A daylighting zone is defined as an area that is “substantially illuminated by daylight.” Previously, 50 per cent of a building’s floor area had to be in daylighting zones;. now it will be 75 per cent (buildings over 5,000 square feet) Installed lighting in these areas must automatically turn off when daylight levels reaches a certain level, even in parking garages .